From c41ca64d075020e2d5daecb7f48da6af0ba5b512 Mon Sep 17 00:00:00 2001
From: Tuomas Tynkkynen <tuomas@tuxera.com>
Date: Wed, 8 Aug 2018 02:25:53 +0300
Subject: ARM: dts: sunxi: Don't use cd-inverted in sun8i-r40-bananapi-m2-ultra
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
index c39b9169ea64..a891a387e8f1 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -159,8 +159,7 @@
&mmc0 {
vmmc-supply = <®_dcdc1>;
bus-width = <4>;
- cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
- cd-inverted;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */
status = "okay";
};
--
cgit 1.2-0.3.lf.el7
From e5c6e693be831c1bba9b4f8f1da597fb5514deca Mon Sep 17 00:00:00 2001
From: Chen-Yu Tsai <wens@csie.org>
Date: Wed, 9 Jan 2019 23:02:55 +0800
Subject: ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator
definitions
The design of the Bananapi M2 Ultra has both DLDO1 and DLDO2 regulators
provide power to the WiFi+BT module, which is based on the Broadcom
BCM43438 or BCM43430 chip. Each regulator output from the PMIC can supply
up to 200 mA. The datasheet of the chip suggests a maximum power draw of
up to 360 mA when transmitting, thus requiring two outputs from the PMIC
to handle the load. However the device tree only references one of them,
leaving the other unused and possibly turned off.
This patch marks both as always-on, since we don't have a proper binding
to specify two regulators as "bound together". The name and constraints
of DLDO2 are also added.
Fixes: da7ac948fa93 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2
Ultra")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
index 438b7b44dab3..1a6794e63b90 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -250,12 +250,27 @@
regulator-name = "vcc-wifi-io";
};
+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
®_dldo2 {
+ regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+};
+
®_dldo4 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
--
cgit 1.2-0.3.lf.el7
From 0729b4af5753b65aa031f58c435da53dbbf56d19 Mon Sep 17 00:00:00 2001
From: Rob Herring <robh@kernel.org>
Date: Thu, 13 Sep 2018 13:12:32 -0500
Subject: ARM: dts: sunxi: Fix I2C bus warnings
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/sun8i-a23-gt90h-v4.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a23-inet86dz.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property
arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property
arch/arm/boot/dts/sun8i-a33-q8-tablet.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2ac00/touchscreen@0: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-utoo-p66.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: I2C bus unit address format error, expected "40"
arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
arch/arm/boot/dts/sun5i-a13-q8-tablet.dtb: Warning (i2c_bus_reg): /soc@1c00000/i2c@1c2b000/touchscreen: missing or empty reg property
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
(limited to 'arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts')
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index 35859d8f3267..bf97f6244c23 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -95,7 +95,7 @@
&i2c0 {
status = "okay";
- axp22x: pmic@68 {
+ axp22x: pmic@34 {
compatible = "x-powers,axp221";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
--
cgit 1.2-0.3.lf.el7
From 933ea7e9d143cee0c8c3bdc274afa69c91d91d61 Mon Sep 17 00:00:00 2001
From: Pablo Greco <pgreco@centosproject.org>
Date: Wed, 10 Apr 2019 18:59:25 -0300
Subject: [PATCH v2 1/6] ARM: dts: sun8i: v40: bananapi-m2-berry: Sort device
node dereferences.
The device node dereferences are out of order, sort them.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 36 +++++++++++------------
1 file changed, 18 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index bf97f62..f05cabd 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -105,6 +105,24 @@
#include "axp22x.dtsi"
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pg_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
®_aldo3 {
regulator-always-on;
regulator-min-microvolt = <2700000>;
@@ -152,24 +170,6 @@
regulator-name = "vcc-wifi";
};
-&mmc0 {
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */
- status = "okay";
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pg_pins>;
- vmmc-supply = <®_dldo2>;
- vqmmc-supply = <®_dldo1>;
- mmc-pwrseq = <&wifi_pwrseq>;
- bus-width = <4>;
- non-removable;
- status = "okay";
-};
-
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
--
1.8.3.1
From 745c1a105e34553caf247215cdcefa30db95092a Mon Sep 17 00:00:00 2001
From: Pablo Greco <pgreco@centosproject.org>
Date: Thu, 11 Apr 2019 13:58:49 -0300
Subject: [PATCH v2 2/6] ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC
ethernet controller
Just like the Bananapi M2 Ultra, the Bananapi M2 Berry has a Realtek
RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 30 +++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index f05cabd..0d79e91 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -50,6 +50,7 @@
compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40";
aliases {
+ ethernet0 = &gmac;
serial0 = &uart0;
};
@@ -92,6 +93,22 @@
status = "okay";
};
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_rgmii_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_dc1sw>;
+ status = "okay";
+};
+
+&gmac_mdio {
+ phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&i2c0 {
status = "okay";
@@ -123,6 +140,13 @@
status = "okay";
};
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa";
+};
+
®_aldo3 {
regulator-always-on;
regulator-min-microvolt = <2700000>;
@@ -130,6 +154,12 @@
regulator-name = "avcc";
};
+®_dc1sw {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-gmac-phy";
+};
+
®_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
--
1.8.3.1
From 274ba1411bac61fcecdf021a13d645891e7b723c Mon Sep 17 00:00:00 2001
From: Pablo Greco <pgreco@centosproject.org>
Date: Thu, 11 Apr 2019 14:00:05 -0300
Subject: [PATCH v2 3/6] ARM: dts: sun8i: v40: bananapi-m2-berry: Enable HDMI
output
This patch adds the hdmi nodes to the Bananapi M2 Berry, the same way it
was done to the Bananapi M2 Ultra
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 29 +++++++++++++++++++++++
1 file changed, 29 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index 0d79e91..2a5b80b 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -58,6 +58,17 @@
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -88,6 +99,10 @@
};
};
+&de {
+ status = "okay";
+};
+
&ehci1 {
/* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */
status = "okay";
@@ -109,6 +124,16 @@
};
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
status = "okay";
@@ -200,6 +225,10 @@
regulator-name = "vcc-wifi";
};
+&tcon_tv0 {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pb_pins>;
--
1.8.3.1
From e91ec82e21aaf29f1453053175050b8230c2b495 Mon Sep 17 00:00:00 2001
From: Pablo Greco <pgreco@centosproject.org>
Date: Thu, 11 Apr 2019 14:03:54 -0300
Subject: [PATCH v2 4/6] ARM: dts: sun8i: v40: bananapi-m2-berry: Enable AHCI
Just like the Bananapi M2 Ultra, enable the ahci controller and
the two regulators needed to activate it.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index 2a5b80b..c37c7ab 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -99,6 +99,12 @@
};
};
+&ahci {
+ ahci-supply = <®_dldo4>;
+ phy-supply = <®_eldo3>;
+ status = "okay";
+};
+
&de {
status = "okay";
};
@@ -225,6 +231,18 @@
regulator-name = "vcc-wifi";
};
+®_dldo4 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vdd2v5-sata";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd1v2-sata";
+};
+
&tcon_tv0 {
status = "okay";
};
--
1.8.3.1
From df95d67e4385275586d3f91ee145f8d13885a560 Mon Sep 17 00:00:00 2001
From: Pablo Greco <pgreco@centosproject.org>
Date: Thu, 11 Apr 2019 14:04:35 -0300
Subject: [PATCH v2 5/6] ARM: dts: sun8i: v40: bananapi-m2-berry: Fix WiFi
regulator definitions
Just like was done for the bananapi-m2-ultra, add the second wifi/bt
regulator and mark both as always-on.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
---
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index c37c7ab..78f4a1a 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -225,12 +225,27 @@
regulator-name = "vcc-wifi-io";
};
+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
®_dldo2 {
+ regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
+®_dldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+};
+
®_dldo4 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
--
1.8.3.1