From 1b28a544627ddce094091946f06f99bc41d0098f Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 24 Oct 2017 19:57:12 +0200
Subject: [PATCH 01/11] net: stmmac: snps, dwmac-mdio MDIOs are automatically
registered
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Since these compatible is automatically registered, dwmac-sun8i compatible
does not need to be in need_mdio_ids.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
---
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 4 ----
1 file changed, 4 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index 6383695004a5..645ef949705f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -318,10 +318,6 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat,
bool mdio = true;
static const struct of_device_id need_mdio_ids[] = {
{ .compatible = "snps,dwc-qos-ethernet-4.10" },
- { .compatible = "allwinner,sun8i-a83t-emac" },
- { .compatible = "allwinner,sun8i-h3-emac" },
- { .compatible = "allwinner,sun8i-v3s-emac" },
- { .compatible = "allwinner,sun50i-a64-emac" },
{},
};
--
2.14.3
From 9a5b1d9a7614b022512744896d889e76f687e90a Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 24 Oct 2017 19:57:13 +0200
Subject: [PATCH 02/11] net: stmmac: dwmac-sun8i: Handle integrated/external
MDIOs
The Allwinner H3 SoC have two distinct MDIO bus, only one could be
active at the same time.
The selection of the active MDIO bus are done via some bits in the EMAC
register of the system controller.
This patch implement this MDIO switch via a custom MDIO-mux.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/stmicro/stmmac/Kconfig | 1 +
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 353 ++++++++++++++--------
2 files changed, 224 insertions(+), 130 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 97035766c291..e28c0d2c58e9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -159,6 +159,7 @@ config DWMAC_SUN8I
tristate "Allwinner sun8i GMAC support"
default ARCH_SUNXI
depends on OF && (ARCH_SUNXI || COMPILE_TEST)
+ select MDIO_BUS_MUX
---help---
Support for Allwinner H3 A83T A64 EMAC ethernet controllers.
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index 39c2122a4f26..b3eb344bb158 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -17,6 +17,7 @@
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/iopoll.h>
+#include <linux/mdio-mux.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of_device.h>
@@ -41,14 +42,14 @@
* This value is used for disabling properly EMAC
* and used as a good starting value in case of the
* boot process(uboot) leave some stuff.
- * @internal_phy: Does the MAC embed an internal PHY
+ * @soc_has_internal_phy: Does the MAC embed an internal PHY
* @support_mii: Does the MAC handle MII
* @support_rmii: Does the MAC handle RMII
* @support_rgmii: Does the MAC handle RGMII
*/
struct emac_variant {
u32 default_syscon_value;
- int internal_phy;
+ bool soc_has_internal_phy;
bool support_mii;
bool support_rmii;
bool support_rgmii;
@@ -61,7 +62,8 @@ struct emac_variant {
* @rst_ephy: reference to the optional EPHY reset for the internal PHY
* @variant: reference to the current board variant
* @regmap: regmap for using the syscon
- * @use_internal_phy: Does the current PHY choice imply using the internal PHY
+ * @internal_phy_powered: Does the internal PHY is enabled
+ * @mux_handle: Internal pointer used by mdio-mux lib
*/
struct sunxi_priv_data {
struct clk *tx_clk;
@@ -70,12 +72,13 @@ struct sunxi_priv_data {
struct reset_control *rst_ephy;
const struct emac_variant *variant;
struct regmap *regmap;
- bool use_internal_phy;
+ bool internal_phy_powered;
+ void *mux_handle;
};
static const struct emac_variant emac_variant_h3 = {
.default_syscon_value = 0x58000,
- .internal_phy = PHY_INTERFACE_MODE_MII,
+ .soc_has_internal_phy = true,
.support_mii = true,
.support_rmii = true,
.support_rgmii = true
@@ -83,20 +86,20 @@ static const struct emac_variant emac_variant_h3 = {
static const struct emac_variant emac_variant_v3s = {
.default_syscon_value = 0x38000,
- .internal_phy = PHY_INTERFACE_MODE_MII,
+ .soc_has_internal_phy = true,
.support_mii = true
};
static const struct emac_variant emac_variant_a83t = {
.default_syscon_value = 0,
- .internal_phy = 0,
+ .soc_has_internal_phy = false,
.support_mii = true,
.support_rgmii = true
};
static const struct emac_variant emac_variant_a64 = {
.default_syscon_value = 0,
- .internal_phy = 0,
+ .soc_has_internal_phy = false,
.support_mii = true,
.support_rmii = true,
.support_rgmii = true
@@ -195,6 +198,9 @@ static const struct emac_variant emac_variant_a64 = {
#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */
#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */
#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */
+#define H3_EPHY_MUX_MASK (H3_EPHY_SHUTDOWN | H3_EPHY_SELECT)
+#define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID 1
+#define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID 2
/* H3/A64 specific bits */
#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */
@@ -634,6 +640,159 @@ static int sun8i_dwmac_reset(struct stmmac_priv *priv)
return 0;
}
+/* Search in mdio-mux node for internal PHY node and get its clk/reset */
+static int get_ephy_nodes(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ struct device_node *mdio_mux, *iphynode;
+ struct device_node *mdio_internal;
+ int ret;
+
+ mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux");
+ if (!mdio_mux) {
+ dev_err(priv->device, "Cannot get mdio-mux node\n");
+ return -ENODEV;
+ }
+
+ mdio_internal = of_find_compatible_node(mdio_mux, NULL,
+ "allwinner,sun8i-h3-mdio-internal");
+ if (!mdio_internal) {
+ dev_err(priv->device, "Cannot get internal_mdio node\n");
+ return -ENODEV;
+ }
+
+ /* Seek for internal PHY */
+ for_each_child_of_node(mdio_internal, iphynode) {
+ gmac->ephy_clk = of_clk_get(iphynode, 0);
+ if (IS_ERR(gmac->ephy_clk))
+ continue;
+ gmac->rst_ephy = of_reset_control_get_exclusive(iphynode, NULL);
+ if (IS_ERR(gmac->rst_ephy)) {
+ ret = PTR_ERR(gmac->rst_ephy);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ continue;
+ }
+ dev_info(priv->device, "Found internal PHY node\n");
+ return 0;
+ }
+ return -ENODEV;
+}
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ int ret;
+
+ if (gmac->internal_phy_powered) {
+ dev_warn(priv->device, "Internal PHY already powered\n");
+ return 0;
+ }
+
+ dev_info(priv->device, "Powering internal PHY\n");
+ ret = clk_prepare_enable(gmac->ephy_clk);
+ if (ret) {
+ dev_err(priv->device, "Cannot enable internal PHY\n");
+ return ret;
+ }
+
+ /* Make sure the EPHY is properly reseted, as U-Boot may leave
+ * it at deasserted state, and thus it may fail to reset EMAC.
+ */
+ reset_control_assert(gmac->rst_ephy);
+
+ ret = reset_control_deassert(gmac->rst_ephy);
+ if (ret) {
+ dev_err(priv->device, "Cannot deassert internal phy\n");
+ clk_disable_unprepare(gmac->ephy_clk);
+ return ret;
+ }
+
+ gmac->internal_phy_powered = true;
+
+ return 0;
+}
+
+static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+{
+ if (!gmac->internal_phy_powered)
+ return 0;
+
+ clk_disable_unprepare(gmac->ephy_clk);
+ reset_control_assert(gmac->rst_ephy);
+ gmac->internal_phy_powered = false;
+ return 0;
+}
+
+/* MDIO multiplexing switch function
+ * This function is called by the mdio-mux layer when it thinks the mdio bus
+ * multiplexer needs to switch.
+ * 'current_child' is the current value of the mux register
+ * 'desired_child' is the value of the 'reg' property of the target child MDIO
+ * node.
+ * The first time this function is called, current_child == -1.
+ * If current_child == desired_child, then the mux is already set to the
+ * correct bus.
+ */
+static int mdio_mux_syscon_switch_fn(int current_child, int desired_child,
+ void *data)
+{
+ struct stmmac_priv *priv = data;
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ u32 reg, val;
+ int ret = 0;
+ bool need_power_ephy = false;
+
+ if (current_child ^ desired_child) {
+ regmap_read(gmac->regmap, SYSCON_EMAC_REG, ®);
+ switch (desired_child) {
+ case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID:
+ dev_info(priv->device, "Switch mux to internal PHY");
+ val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT;
+
+ need_power_ephy = true;
+ break;
+ case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID:
+ dev_info(priv->device, "Switch mux to external PHY");
+ val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN;
+ need_power_ephy = false;
+ break;
+ default:
+ dev_err(priv->device, "Invalid child ID %x\n",
+ desired_child);
+ return -EINVAL;
+ }
+ regmap_write(gmac->regmap, SYSCON_EMAC_REG, val);
+ if (need_power_ephy) {
+ ret = sun8i_dwmac_power_internal_phy(priv);
+ if (ret)
+ return ret;
+ } else {
+ sun8i_dwmac_unpower_internal_phy(gmac);
+ }
+ /* After changing syscon value, the MAC need reset or it will
+ * use the last value (and so the last PHY set).
+ */
+ ret = sun8i_dwmac_reset(priv);
+ }
+ return ret;
+}
+
+static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv)
+{
+ int ret;
+ struct device_node *mdio_mux;
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+
+ mdio_mux = of_get_child_by_name(priv->device->of_node, "mdio-mux");
+ if (!mdio_mux)
+ return -ENODEV;
+
+ ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn,
+ &gmac->mux_handle, priv, priv->mii);
+ return ret;
+}
+
static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
{
struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
@@ -648,35 +807,25 @@ static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
"Current syscon value is not the default %x (expect %x)\n",
val, reg);
- if (gmac->variant->internal_phy) {
- if (!gmac->use_internal_phy) {
- /* switch to external PHY interface */
- reg &= ~H3_EPHY_SELECT;
- } else {
- reg |= H3_EPHY_SELECT;
- reg &= ~H3_EPHY_SHUTDOWN;
- dev_dbg(priv->device, "Select internal_phy %x\n", reg);
-
- if (of_property_read_bool(priv->plat->phy_node,
- "allwinner,leds-active-low"))
- reg |= H3_EPHY_LED_POL;
- else
- reg &= ~H3_EPHY_LED_POL;
-
- /* Force EPHY xtal frequency to 24MHz. */
- reg |= H3_EPHY_CLK_SEL;
-
- ret = of_mdio_parse_addr(priv->device,
- priv->plat->phy_node);
- if (ret < 0) {
- dev_err(priv->device, "Could not parse MDIO addr\n");
- return ret;
- }
- /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
- * address. No need to mask it again.
- */
- reg |= ret << H3_EPHY_ADDR_SHIFT;
+ if (gmac->variant->soc_has_internal_phy) {
+ if (of_property_read_bool(priv->plat->phy_node,
+ "allwinner,leds-active-low"))
+ reg |= H3_EPHY_LED_POL;
+ else
+ reg &= ~H3_EPHY_LED_POL;
+
+ /* Force EPHY xtal frequency to 24MHz. */
+ reg |= H3_EPHY_CLK_SEL;
+
+ ret = of_mdio_parse_addr(priv->device, priv->plat->phy_node);
+ if (ret < 0) {
+ dev_err(priv->device, "Could not parse MDIO addr\n");
+ return ret;
}
+ /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+ * address. No need to mask it again.
+ */
+ reg |= 1 << H3_EPHY_ADDR_SHIFT;
}
if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {
@@ -746,81 +895,21 @@ static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac)
regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
}
-static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
{
- struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
- int ret;
-
- if (!gmac->use_internal_phy)
- return 0;
-
- ret = clk_prepare_enable(gmac->ephy_clk);
- if (ret) {
- dev_err(priv->device, "Cannot enable ephy\n");
- return ret;
- }
-
- /* Make sure the EPHY is properly reseted, as U-Boot may leave
- * it at deasserted state, and thus it may fail to reset EMAC.
- */
- reset_control_assert(gmac->rst_ephy);
+ struct sunxi_priv_data *gmac = priv;
- ret = reset_control_deassert(gmac->rst_ephy);
- if (ret) {
- dev_err(priv->device, "Cannot deassert ephy\n");
- clk_disable_unprepare(gmac->ephy_clk);
- return ret;
+ if (gmac->variant->soc_has_internal_phy) {
+ /* sun8i_dwmac_exit could be called with mdiomux uninit */
+ if (gmac->mux_handle)
+ mdio_mux_uninit(gmac->mux_handle);
+ if (gmac->internal_phy_powered)
+ sun8i_dwmac_unpower_internal_phy(gmac);
}
- return 0;
-}
-
-static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
-{
- if (!gmac->use_internal_phy)
- return 0;
-
- clk_disable_unprepare(gmac->ephy_clk);
- reset_control_assert(gmac->rst_ephy);
- return 0;
-}
-
-/* sun8i_power_phy() - Activate the PHY:
- * In case of error, no need to call sun8i_unpower_phy(),
- * it will be called anyway by sun8i_dwmac_exit()
- */
-static int sun8i_power_phy(struct stmmac_priv *priv)
-{
- int ret;
-
- ret = sun8i_dwmac_power_internal_phy(priv);
- if (ret)
- return ret;
-
- ret = sun8i_dwmac_set_syscon(priv);
- if (ret)
- return ret;
-
- /* After changing syscon value, the MAC need reset or it will use
- * the last value (and so the last PHY set.
- */
- ret = sun8i_dwmac_reset(priv);
- if (ret)
- return ret;
- return 0;
-}
-
-static void sun8i_unpower_phy(struct sunxi_priv_data *gmac)
-{
sun8i_dwmac_unset_syscon(gmac);
- sun8i_dwmac_unpower_internal_phy(gmac);
-}
-
-static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
-{
- struct sunxi_priv_data *gmac = priv;
- sun8i_unpower_phy(gmac);
+ reset_control_put(gmac->rst_ephy);
clk_disable_unprepare(gmac->tx_clk);
@@ -849,7 +938,7 @@ static struct mac_device_info *sun8i_dwmac_setup(void *ppriv)
if (!mac)
return NULL;
- ret = sun8i_power_phy(priv);
+ ret = sun8i_dwmac_set_syscon(priv);
if (ret)
return NULL;
@@ -889,6 +978,8 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
struct sunxi_priv_data *gmac;
struct device *dev = &pdev->dev;
int ret;
+ struct stmmac_priv *priv;
+ struct net_device *ndev;
ret = stmmac_get_platform_resources(pdev, &stmmac_res);
if (ret)
@@ -932,29 +1023,6 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
}
plat_dat->interface = of_get_phy_mode(dev->of_node);
- if (plat_dat->interface == gmac->variant->internal_phy) {
- dev_info(&pdev->dev, "Will use internal PHY\n");
- gmac->use_internal_phy = true;
- gmac->ephy_clk = of_clk_get(plat_dat->phy_node, 0);
- if (IS_ERR(gmac->ephy_clk)) {
- ret = PTR_ERR(gmac->ephy_clk);
- dev_err(&pdev->dev, "Cannot get EPHY clock: %d\n", ret);
- return -EINVAL;
- }
-
- gmac->rst_ephy = of_reset_control_get(plat_dat->phy_node, NULL);
- if (IS_ERR(gmac->rst_ephy)) {
- ret = PTR_ERR(gmac->rst_ephy);
- if (ret == -EPROBE_DEFER)
- return ret;
- dev_err(&pdev->dev, "No EPHY reset control found %d\n",
- ret);
- return -EINVAL;
- }
- } else {
- dev_info(&pdev->dev, "Will use external PHY\n");
- gmac->use_internal_phy = false;
- }
/* platform data specifying hardware features and callbacks.
* hardware features were copied from Allwinner drivers.
@@ -973,9 +1041,34 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
if (ret)
- sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+ goto dwmac_exit;
+
+ ndev = dev_get_drvdata(&pdev->dev);
+ priv = netdev_priv(ndev);
+ /* The mux must be registered after parent MDIO
+ * so after stmmac_dvr_probe()
+ */
+ if (gmac->variant->soc_has_internal_phy) {
+ ret = get_ephy_nodes(priv);
+ if (ret)
+ goto dwmac_exit;
+ ret = sun8i_dwmac_register_mdio_mux(priv);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register mux\n");
+ goto dwmac_mux;
+ }
+ } else {
+ ret = sun8i_dwmac_reset(priv);
+ if (ret)
+ goto dwmac_exit;
+ }
return ret;
+dwmac_mux:
+ sun8i_dwmac_unset_syscon(gmac);
+dwmac_exit:
+ sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+return ret;
}
static const struct of_device_id sun8i_dwmac_match[] = {
--
2.14.3
From f58f11ebb67468471ed8f232c576f348dd1a32b1 Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 24 Oct 2017 19:57:14 +0200
Subject: [PATCH 03/11] net: stmmac: sun8i: Restore the compatibles
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore compatibles about dwmac-sun8i
This reverts commit ad4540cc5aa3 ("net: stmmac: sun8i: Remove the compatibles")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index b3eb344bb158..e5ff734d4f9b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -1072,6 +1072,14 @@ return ret;
}
static const struct of_device_id sun8i_dwmac_match[] = {
+ { .compatible = "allwinner,sun8i-h3-emac",
+ .data = &emac_variant_h3 },
+ { .compatible = "allwinner,sun8i-v3s-emac",
+ .data = &emac_variant_v3s },
+ { .compatible = "allwinner,sun8i-a83t-emac",
+ .data = &emac_variant_a83t },
+ { .compatible = "allwinner,sun50i-a64-emac",
+ .data = &emac_variant_a64 },
{ }
};
MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
--
2.14.3
From 54678636d98cd9625f342c831015e302642bf104 Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 31 Oct 2017 09:19:08 +0100
Subject: [PATCH 04/11] dt-bindings: net: Restore sun8i dwmac binding
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore dt-bindings documentation about dwmac-sun8i
This reverts commit 8aa33ec2f481 ("dt-bindings: net: Revert sun8i dwmac binding")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
.../devicetree/bindings/net/dwmac-sun8i.txt | 84 ++++++++++++++++++++++
1 file changed, 84 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/dwmac-sun8i.txt
diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
new file mode 100644
index 000000000000..725f3b187886
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
@@ -0,0 +1,84 @@
+* Allwinner sun8i GMAC ethernet controller
+
+This device is a platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+Required properties:
+- compatible: should be one of the following string:
+ "allwinner,sun8i-a83t-emac"
+ "allwinner,sun8i-h3-emac"
+ "allwinner,sun8i-v3s-emac"
+ "allwinner,sun50i-a64-emac"
+- reg: address and length of the register for the device.
+- interrupts: interrupt for the device
+- interrupt-names: should be "macirq"
+- clocks: A phandle to the reference clock for this device
+- clock-names: should be "stmmaceth"
+- resets: A phandle to the reset control for this device
+- reset-names: should be "stmmaceth"
+- phy-mode: See ethernet.txt
+- phy-handle: See ethernet.txt
+- #address-cells: shall be 1
+- #size-cells: shall be 0
+- syscon: A phandle to the syscon of the SoC with one of the following
+ compatible string:
+ - allwinner,sun8i-h3-system-controller
+ - allwinner,sun8i-v3s-system-controller
+ - allwinner,sun50i-a64-system-controller
+ - allwinner,sun8i-a83t-system-controller
+
+Optional properties:
+- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0)
+- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0)
+Both delay properties need to be a multiple of 100. They control the delay for
+external PHY.
+
+Optional properties for the following compatibles:
+ - "allwinner,sun8i-h3-emac",
+ - "allwinner,sun8i-v3s-emac":
+- allwinner,leds-active-low: EPHY LEDs are active low
+
+Required child node of emac:
+- mdio bus node: should be named mdio
+
+Required properties of the mdio node:
+- #address-cells: shall be 1
+- #size-cells: shall be 0
+
+The device node referenced by "phy" or "phy-handle" should be a child node
+of the mdio node. See phy.txt for the generic PHY bindings.
+
+Required properties of the phy node with the following compatibles:
+ - "allwinner,sun8i-h3-emac",
+ - "allwinner,sun8i-v3s-emac":
+- clocks: a phandle to the reference clock for the EPHY
+- resets: a phandle to the reset control for the EPHY
+
+Example:
+
+emac: ethernet@1c0b000 {
+ compatible = "allwinner,sun8i-h3-emac";
+ syscon = <&syscon>;
+ reg = <0x01c0b000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ int_mii_phy: ethernet-phy@1 {
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+};
--
2.14.3
From 227bc8c6bfad58c32c7a6c3bbc13d99eb6d266c0 Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 31 Oct 2017 09:19:09 +0100
Subject: [PATCH 05/11] dt-bindings: net: dwmac-sun8i: update documentation
about integrated PHY
This patch add documentation about the MDIO switch used on sun8i-h3-emac
for integrated PHY.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
.../devicetree/bindings/net/dwmac-sun8i.txt | 147 +++++++++++++++++++--
1 file changed, 135 insertions(+), 12 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
index 725f3b187886..3d6d5fa0c4d5 100644
--- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
+++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
@@ -4,18 +4,18 @@ This device is a platform glue layer for stmmac.
Please see stmmac.txt for the other unchanged properties.
Required properties:
-- compatible: should be one of the following string:
+- compatible: must be one of the following string:
"allwinner,sun8i-a83t-emac"
"allwinner,sun8i-h3-emac"
"allwinner,sun8i-v3s-emac"
"allwinner,sun50i-a64-emac"
- reg: address and length of the register for the device.
- interrupts: interrupt for the device
-- interrupt-names: should be "macirq"
+- interrupt-names: must be "macirq"
- clocks: A phandle to the reference clock for this device
-- clock-names: should be "stmmaceth"
+- clock-names: must be "stmmaceth"
- resets: A phandle to the reset control for this device
-- reset-names: should be "stmmaceth"
+- reset-names: must be "stmmaceth"
- phy-mode: See ethernet.txt
- phy-handle: See ethernet.txt
- #address-cells: shall be 1
@@ -39,23 +39,42 @@ Optional properties for the following compatibles:
- allwinner,leds-active-low: EPHY LEDs are active low
Required child node of emac:
-- mdio bus node: should be named mdio
+- mdio bus node: should be named mdio with compatible "snps,dwmac-mdio"
Required properties of the mdio node:
- #address-cells: shall be 1
- #size-cells: shall be 0
-The device node referenced by "phy" or "phy-handle" should be a child node
+The device node referenced by "phy" or "phy-handle" must be a child node
of the mdio node. See phy.txt for the generic PHY bindings.
-Required properties of the phy node with the following compatibles:
+The following compatibles require that the emac node have a mdio-mux child
+node called "mdio-mux":
+ - "allwinner,sun8i-h3-emac"
+ - "allwinner,sun8i-v3s-emac":
+Required properties for the mdio-mux node:
+ - compatible = "allwinner,sun8i-h3-mdio-mux"
+ - mdio-parent-bus: a phandle to EMAC mdio
+ - one child mdio for the integrated mdio with the compatible
+ "allwinner,sun8i-h3-mdio-internal"
+ - one child mdio for the external mdio if present (V3s have none)
+Required properties for the mdio-mux children node:
+ - reg: 1 for internal MDIO bus, 2 for external MDIO bus
+
+The following compatibles require a PHY node representing the integrated
+PHY, under the integrated MDIO bus node if an mdio-mux node is used:
- "allwinner,sun8i-h3-emac",
- "allwinner,sun8i-v3s-emac":
+
+Additional information regarding generic multiplexer properties can be found
+at Documentation/devicetree/bindings/net/mdio-mux.txt
+
+Required properties of the integrated phy node:
- clocks: a phandle to the reference clock for the EPHY
- resets: a phandle to the reset control for the EPHY
+- Must be a child of the integrated mdio
-Example:
-
+Example with integrated PHY:
emac: ethernet@1c0b000 {
compatible = "allwinner,sun8i-h3-emac";
syscon = <&syscon>;
@@ -72,13 +91,117 @@ emac: ethernet@1c0b000 {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+
+ mdio-mux {
+ compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio-parent-bus = <&mdio>;
+
+ int_mdio: mdio@1 {
+ compatible = "allwinner,sun8i-h3-mdio-internal";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ int_mii_phy: ethernet-phy@1 {
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ phy-is-integrated;
+ };
+ };
+ ext_mdio: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+Example with external PHY:
+emac: ethernet@1c0b000 {
+ compatible = "allwinner,sun8i-h3-emac";
+ syscon = <&syscon>;
+ reg = <0x01c0b000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ allwinner,leds-active-low;
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+
+ mdio-mux {
+ compatible = "allwinner,sun8i-h3-mdio-mux";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio-parent-bus = <&mdio>;
+
+ int_mdio: mdio@1 {
+ compatible = "allwinner,sun8i-h3-mdio-internal";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ int_mii_phy: ethernet-phy@1 {
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+ ext_mdio: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ext_rgmii_phy: ethernet-phy@1 {
+ reg = <1>;
+ };
+ }:
+ };
+};
+
+Example with SoC without integrated PHY
+
+emac: ethernet@1c0b000 {
+ compatible = "allwinner,sun8i-a83t-emac";
+ syscon = <&syscon>;
+ reg = <0x01c0b000 0x104>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
mdio: mdio {
+ compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;
- int_mii_phy: ethernet-phy@1 {
+ ext_rgmii_phy: ethernet-phy@1 {
reg = <1>;
- clocks = <&ccu CLK_BUS_EPHY>;
- resets = <&ccu RST_BUS_EPHY>;
};
};
};
--
2.14.3
From 1de79efa35a1130c7a085f62b9d9b666d79b9a89 Mon Sep 17 00:00:00 2001
From: Peter Robinson <pbrobinson@gmail.com>
Date: Wed, 1 Nov 2017 14:04:20 +0000
Subject: [PATCH 06/11] arm: dts: sunxi: h3/h5: Restore EMAC changes
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore sunxi-h3-h5.dtsi
This reverts partially commit fe45174b72ae ("arm: dts: sunxi: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index 11240a8313c2..d38282b9e5d4 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -391,6 +391,32 @@
clocks = <&osc24M>;
};
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun8i-h3-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ int_mii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+ };
+
spi0: spi@01c68000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>;
--
2.14.3
From 65233cba93184e0efa8d94f907d65af947d197a1 Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 31 Oct 2017 09:19:11 +0100
Subject: [PATCH 07/11] ARM: dts: sunxi: h3/h5: represent the mdio switch used
by sun8i-h3-emac
Since dwmac-sun8i could use either an integrated PHY or an external PHY
(which could be at same MDIO address), we need to represent this selection
by a MDIO switch.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm/boot/dts/sunxi-h3-h5.dtsi | 31 +++++++++++++++++++++++++++----
1 file changed, 27 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index d38282b9e5d4..2721b39c1875 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -408,11 +408,34 @@
mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
- int_mii_phy: ethernet-phy@1 {
- compatible = "ethernet-phy-ieee802.3-c22";
+ compatible = "snps,dwmac-mdio";
+ };
+
+ mdio-mux {
+ compatible = "allwinner,sun8i-h3-mdio-mux";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio-parent-bus = <&mdio>;
+ /* Only one MDIO is usable at the time */
+ internal_mdio: mdio@1 {
+ compatible = "allwinner,sun8i-h3-mdio-internal";
reg = <1>;
- clocks = <&ccu CLK_BUS_EPHY>;
- resets = <&ccu RST_BUS_EPHY>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ int_mii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+
+ external_mdio: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
};
};
};
--
2.14.3
From b705315d36dbe1b31062f30c987b3a502b437c85 Mon Sep 17 00:00:00 2001
From: Peter Robinson <pbrobinson@gmail.com>
Date: Wed, 1 Nov 2017 14:08:45 +0000
Subject: [PATCH 08/11] ARM: dts: sunxi: Restore EMAC changes (boards)
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore all boards DT about dwmac-sun8i
This reverts partially commit fe45174b72ae ("arm: dts: sunxi: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts | 9 +++++++++
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts | 19 +++++++++++++++++++
arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 19 +++++++++++++++++++
arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts | 7 +++++++
arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 8 ++++++++
arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 8 ++++++++
arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts | 5 +++++
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 8 ++++++++
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 22 ++++++++++++++++++++++
arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts | 16 ++++++++++++++++
10 files changed, 121 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
index b1502df7b509..6713d0f2b3f4 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -56,6 +56,8 @@
aliases {
serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
ethernet1 = &xr819;
};
@@ -102,6 +104,13 @@
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index a337af1de322..3f95d806355b 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -52,6 +52,7 @@
compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
@@ -114,6 +115,24 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
index 8ddd1b2cc097..ef0371811296 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -62,3 +62,22 @@
&ohci2 {
status = "okay";
};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ allwinner,leds-active-low;
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
index 8d2cc6e9a03f..78f6c24952dd 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
@@ -46,3 +46,10 @@
model = "FriendlyARM NanoPi NEO";
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
index 8ff71b1bb45b..17cdeae19c6f 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
@@ -54,6 +54,7 @@
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
ethernet1 = &rtl8189;
};
@@ -117,6 +118,13 @@
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
index 5fea430e0eb1..6880268e8b87 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
@@ -52,6 +52,7 @@
compatible = "xunlong,orangepi-one", "allwinner,sun8i-h3";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -97,6 +98,13 @@
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
index 8b93f5c781a7..a10281b455f5 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
@@ -53,6 +53,11 @@
};
};
+&emac {
+ /* LEDs changed to active high on the plus */
+ /delete-property/ allwinner,leds-active-low;
+};
+
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index 1a044b17d6c6..998b60f8d295 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -52,6 +52,7 @@
compatible = "xunlong,orangepi-pc", "allwinner,sun8i-h3";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -113,6 +114,13 @@
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
index 828ae7a526d9..3002c025e187 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -47,6 +47,10 @@
model = "Xunlong Orange Pi Plus / Plus 2";
compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+ aliases {
+ ethernet0 = &emac;
+ };
+
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
regulator-name = "gmac-3v3";
@@ -74,6 +78,24 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
index 97920b12a944..6dbf7b2e0c13 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
@@ -61,3 +61,19 @@
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
};
};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
--
2.14.3
From 516b88bfa40cf54732d2ba5e689fdf592a742ec3 Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 31 Oct 2017 09:19:13 +0100
Subject: [PATCH 09/11] arm64: dts: allwinner: A64: Restore EMAC changes
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for A64
This reverts commit 87e1f5e8bb4b ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
.../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 16 ++++++++++++++++
.../boot/dts/allwinner/sun50i-a64-pine64-plus.dts | 15 +++++++++++++++
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 17 +++++++++++++++++
.../dts/allwinner/sun50i-a64-sopine-baseboard.dts | 16 ++++++++++++++++
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 20 ++++++++++++++++++++
5 files changed, 84 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index d347f52e27f6..45bdbfb96126 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -51,6 +51,7 @@
compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
@@ -69,6 +70,14 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
@@ -79,6 +88,13 @@
bias-pull-up;
};
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
index f82ccf332c0f..24f1aac366d6 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
@@ -48,3 +48,18 @@
/* TODO: Camera, touchscreen, etc. */
};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
index d06e34b5d192..806442d3e846 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -51,6 +51,7 @@
compatible = "pine64,pine64", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
@@ -71,6 +72,15 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rmii_pins>;
+ phy-mode = "rmii";
+ phy-handle = <&ext_rmii_phy1>;
+ status = "okay";
+
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
@@ -81,6 +91,13 @@
bias-pull-up;
};
+&mdio {
+ ext_rmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
index 17ccc12b58df..0eb2acedf8c3 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
@@ -53,6 +53,7 @@
"allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -76,6 +77,21 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 8c8db1b057df..50f17bab0c07 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -449,6 +449,26 @@
#size-cells = <0>;
};
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun50i-a64-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
gic: interrupt-controller@1c81000 {
compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
--
2.14.3
From 070173449eb88e9cf9c91889c77f53616911f4d0 Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 31 Oct 2017 09:19:14 +0100
Subject: [PATCH 10/11] arm64: dts: allwinner: H5: Restore EMAC changes
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for H5
This reverts a part of commit 87e1f5e8bb4b ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts | 17 +++++++++++++++++
.../arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 17 +++++++++++++++++
.../boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 17 +++++++++++++++++
3 files changed, 51 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts
index 1c2387bd5df6..6eb8092d8e57 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts
@@ -50,6 +50,7 @@
compatible = "friendlyarm,nanopi-neo2", "allwinner,sun50i-h5";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -108,6 +109,22 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
index 4f77c8470f6c..a0ca925175aa 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -59,6 +59,7 @@
};
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -136,6 +137,22 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
index 6be06873e5af..b47790650144 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
@@ -54,6 +54,7 @@
compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -143,6 +144,22 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
--
2.14.3
From 63118a9f7808a0a67c23e7d276138c996e094eae Mon Sep 17 00:00:00 2001
From: Corentin LABBE <clabbe.montjoie@gmail.com>
Date: Tue, 31 Oct 2017 09:19:15 +0100
Subject: [PATCH 11/11] arm64: dts: allwinner: add snps, dwmac-mdio compatible
to emac/mdio
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 50f17bab0c07..8fd75c95937a 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -464,6 +464,7 @@
#size-cells = <0>;
mdio: mdio {
+ compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;
};
--
2.14.3
From patchwork Fri Nov 10 09:26:54 2017
Content-Type: text/plain; charset="utf-8"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Subject: arm64: allwinner: a64: add Ethernet PHY regulator for several boards
From: Icenowy Zheng <icenowy@aosc.io>
X-Patchwork-Id: 10052659
Message-Id: <20171110092654.10746-1-icenowy@aosc.io>
To: Maxime Ripard <maxime.ripard@free-electrons.com>,
Chen-Yu Tsai <wens@csie.org>
Cc: linux-sunxi@googlegroups.com, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, Icenowy Zheng <icenowy@aosc.io>
Date: Fri, 10 Nov 2017 17:26:54 +0800
On several A64 boards the Ethernet PHY is powered by the DC1SW regulator
on the AXP803 PMIC.
Add phy-handle property to these boards' emac node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com>
---
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 1 +
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 1 +
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts | 1 +
3 files changed, 3 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index 45bdbfb96126..4a8d3f83a36e 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -75,6 +75,7 @@
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dc1sw>;
status = "okay";
};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
index 806442d3e846..604cdaedac38 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -77,6 +77,7 @@
pinctrl-0 = <&rmii_pins>;
phy-mode = "rmii";
phy-handle = <&ext_rmii_phy1>;
+ phy-supply = <®_dc1sw>;
status = "okay";
};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
index 0eb2acedf8c3..a053a6ac5267 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
@@ -82,6 +82,7 @@
pinctrl-0 = <&rgmii_pins>;
phy-mode = "rgmii";
phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dc1sw>;
status = "okay";
};
From 79e7d6c8bfe67fce8c8fe4953e74ce7f420dd732 Mon Sep 17 00:00:00 2001
From: Peter Robinson <pbrobinson@gmail.com>
Date: Tue, 21 Nov 2017 15:43:19 +0000
Subject: [PATCH] ARM: dts: sunxi: sun8i-h3-nanopi-m1-plus: Add missing
regulator
This patch add the missing regulator for sun8i-h3-nanopi-m1-plus.
Fixes: ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
---
arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
index ef0371811296..738ef1d9e844 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -45,6 +45,17 @@
/ {
model = "FriendlyArm NanoPi M1 Plus";
compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3";
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
};
&ehci1 {
--
2.14.3
From 4497478c60c04d2bf37082e27fc98f4f835db96b Mon Sep 17 00:00:00 2001
From: Niklas Cassel <niklas.cassel@axis.com>
Date: Tue, 14 Nov 2017 11:15:54 +0100
Subject: net: stmmac: fix LPI transitioning for dwmac4
The LPI transitioning logic in stmmac_main uses
priv->tx_path_in_lpi_mode to enter/exit LPI.
However, priv->tx_path_in_lpi_mode is assigned
using the return value from host_irq_status().
So for dwmac4, priv->tx_path_in_lpi_mode was always false,
so stmmac_tx_clean() would always try to put us in eee mode,
and stmmac_xmit() would never take us out of eee mode.
To fix this, make host_irq_status() read and return the LPI
irq status also for dwmac4.
This also increments the existing LPI counters, so that
ethtool --statistics shows LPI transitions also for dwmac4.
For dwmac1000, irqs are enabled/disabled using the register
named "Interrupt Mask Register", and thus setting a bit disables
that specific irq.
For dwmac4 the matching register is named "MAC_Interrupt_Enable",
and thus setting a bit enables that specific irq.
Looking at dwmac1000_core.c, the irqs that are always enabled are:
LPI and PMT.
Looking at dwmac4_core.c, the irqs that are always enabled are:
PMT.
To be able to read the LPI irq status, we need to enable the LPI
irq also for dwmac4.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
drivers/net/ethernet/stmicro/stmmac/dwmac4.h | 7 ++++++-
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 19 +++++++++++++++++++
2 files changed, 25 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
index aeda3ab..789dad8 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4.h
@@ -98,7 +98,7 @@
#define GMAC_PCS_IRQ_DEFAULT (GMAC_INT_RGSMIIS | GMAC_INT_PCS_LINK | \
GMAC_INT_PCS_ANE)
-#define GMAC_INT_DEFAULT_MASK GMAC_INT_PMT_EN
+#define GMAC_INT_DEFAULT_MASK (GMAC_INT_PMT_EN | GMAC_INT_LPI_EN)
enum dwmac4_irq_status {
time_stamp_irq = 0x00001000,
@@ -106,6 +106,7 @@ enum dwmac4_irq_status {
mmc_tx_irq = 0x00000400,
mmc_rx_irq = 0x00000200,
mmc_irq = 0x00000100,
+ lpi_irq = 0x00000020,
pmt_irq = 0x00000010,
};
@@ -132,6 +133,10 @@ enum power_event {
#define GMAC4_LPI_CTRL_STATUS_LPITXA BIT(19) /* Enable LPI TX Automate */
#define GMAC4_LPI_CTRL_STATUS_PLS BIT(17) /* PHY Link Status */
#define GMAC4_LPI_CTRL_STATUS_LPIEN BIT(16) /* LPI Enable */
+#define GMAC4_LPI_CTRL_STATUS_RLPIEX BIT(3) /* Receive LPI Exit */
+#define GMAC4_LPI_CTRL_STATUS_RLPIEN BIT(2) /* Receive LPI Entry */
+#define GMAC4_LPI_CTRL_STATUS_TLPIEX BIT(1) /* Transmit LPI Exit */
+#define GMAC4_LPI_CTRL_STATUS_TLPIEN BIT(0) /* Transmit LPI Entry */
/* MAC Debug bitmap */
#define GMAC_DEBUG_TFCSTS_MASK GENMASK(18, 17)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
index 2f7d7ec..f3ed8f7 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c
@@ -580,6 +580,25 @@ static int dwmac4_irq_status(struct mac_device_info *hw,
x->irq_receive_pmt_irq_n++;
}
+ /* MAC tx/rx EEE LPI entry/exit interrupts */
+ if (intr_status & lpi_irq) {
+ /* Clear LPI interrupt by reading MAC_LPI_Control_Status */
+ u32 status = readl(ioaddr + GMAC4_LPI_CTRL_STATUS);
+
+ if (status & GMAC4_LPI_CTRL_STATUS_TLPIEN) {
+ ret |= CORE_IRQ_TX_PATH_IN_LPI_MODE;
+ x->irq_tx_path_in_lpi_mode_n++;
+ }
+ if (status & GMAC4_LPI_CTRL_STATUS_TLPIEX) {
+ ret |= CORE_IRQ_TX_PATH_EXIT_LPI_MODE;
+ x->irq_tx_path_exit_lpi_mode_n++;
+ }
+ if (status & GMAC4_LPI_CTRL_STATUS_RLPIEN)
+ x->irq_rx_path_in_lpi_mode_n++;
+ if (status & GMAC4_LPI_CTRL_STATUS_RLPIEX)
+ x->irq_rx_path_exit_lpi_mode_n++;
+ }
+
dwmac_pcs_isr(ioaddr, GMAC_PCS_BASE, intr_status, x);
if (intr_status & PCS_RGSMIIIS_IRQ)
dwmac4_phystatus(ioaddr, x);
--
cgit v1.1
From 1c08ac0c4bd8e9d66c4dde29bc496c3b430dd028 Mon Sep 17 00:00:00 2001
From: Corentin Labbe <clabbe.montjoie@gmail.com>
Date: Tue, 28 Nov 2017 17:48:22 +0100
Subject: net: stmmac: dwmac-sun8i: fix allwinner,leds-active-low handling
The driver expect "allwinner,leds-active-low" to be in PHY node, but
the binding doc expect it to be in MAC node.
Since all board DT use it also in MAC node, the driver need to search
allwinner,leds-active-low in MAC node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index e5ff734..9eb7f65 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -808,8 +808,7 @@ static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
val, reg);
if (gmac->variant->soc_has_internal_phy) {
- if (of_property_read_bool(priv->plat->phy_node,
- "allwinner,leds-active-low"))
+ if (of_property_read_bool(node, "allwinner,leds-active-low"))
reg |= H3_EPHY_LED_POL;
else
reg &= ~H3_EPHY_LED_POL;
--
cgit v1.1