MKSQUASHFS(1)

NAME
mksquashfs - tool to create and append to squashfs filesystems

SYNOPSIS
mksquashfs source1 source2 ... FILESYSTEM [OPTIONS] [-e list of exclude dirs/files]

DESCRIPTION
Squashfs is a highly compressed read-only filesystem for Linux. It uses either gzip/xz/lzo/lz4/zstd compression to compress both files, inodes and directories. Inodes in the system are very small and all blocks are packed to minimise data overhead. Block sizes greater than 4K are supported up to a maximum of 1Mbytes (default block size 128K). Squashfs is intended for general read-only filesystem use, for archival use (i.e. in cases where a .tar.gz file may be used), and in constrained block device/memory systems (e.g. embedded systems) where low overhead is needed.

OPTIONS

  Filesystem build options:

-tar
    read uncompressed tar file from standard in (stdin).

-no-strip
    act like tar, and do not strip leading directories from source files.

-tarstyle
    alternative name for -no-strip.

-cpiostyle
    act like cpio, and read files from standard in (stdin).

-cpiostyle0
    like -cpiostyle, but filenames are null terminated.

-comp COMP
    select COMP compression. Compressors available: gzip (default), lzo, lz4, xz, zstd.

-b BLOCK_SIZE
    set data block to BLOCK_SIZE. Default 128 Kbytes. Optionally a suffix of K or M can be given to specify Kbytes or Mbytes respectively.

-reproducible
    build filesystems that are reproducible (default).

-not-reproducible
    build filesystems that are not reproducible.

-mkfs-time TIME
    set filesystem creation timestamp to TIME, which is an unsigned 32-bit int indicating seconds since the epoch (1970-01-01).

-fstime TIME
    synonym for mkfs-time.

-all-time TIME
    set all file timestamps to TIME, which is an unsigned 32-bit int indicating seconds since the epoch (1970-01-01).

-no-exports
    don't make filesystem exportable via NFS (-tar default).

-exports
    make filesystem exportable via NFS (default).

-no-sparse
    don't detect sparse files.

-no-xattrs
    don't store extended attributes.

-xattrs
    store extended attributes (default).

-noI
    do not compress inode table.

-noId
    do not compress the uid/gid table (implied by -noI).

-noD
    do not compress data blocks.

-noF
    do not compress fragment blocks.

-noX
    do not compress extended attributes.

-no-tailends
    don't pack tail ends into fragments (default).

-tailends
    pack tail ends into fragments.

-no-fragments
    do not use fragments.

-always-use-fragments
    use fragment blocks for files larger than block size.

-no-duplicates
    do not perform duplicate checking.

-no-hardlinks
    do not hardlink files, instead store duplicates.

-all-root
    make all files owned by root.

-root-time TIME
    set root directory time to TIME.

-root-mode MODE
    set root directory permissions to octal MODE.

-root-uid UID
    set root directory owner to UID.

-root-gid GID
    set root directory group to GID.

-force-uid UID
    set all file uids to UID.

-force-gid GID
    set all file gids to GID.

-keep-as-directory
    if one source directory is specified, create a root directory containing that directory, rather than the contents of the directory.

-action ACTION@EXPRESSION
    evaluate EXPRESSION on every file, and execute ACTION if it returns TRUE.

-log-action ACTION@EXPRESSION
    as above, but log expression evaluation results and actions performed.

-true-action ACTION@EXPRESSION
    as above, but only log expressions which return TRUE.

-false-action ACTION@EXPRESSION
    as above, but only log expressions which return FALSE.

-action-file FILE
    as action, but read actions from FILE.

-log-action-file FILE
    as -log-action, but read actions from FILE.

-true-action-file FILE
    as -true-action, but read actions from FILE.

-false-action-file FILE
    as -false-action, but read actions from FILE.

  Filesystem filter options:

-p PSEUDO-DEFINITION
    Add pseudo file definition. The definition should be quoted.

-pf PSEUDO-FILE
    Add list of pseudo file definitions. Pseudo file definitions in pseudo-files should not be quoted.

-sort SORT_FILE
    sort files according to priorities in SORT_FILE. One file or dir with priority per line. Priority -32768 to 32767, default priority 0.

-ef EXCLUDE_FILE
    list of exclude dirs/files. One per line.

-wildcards
    Allow extended shell wildcards (globbing) to be used in exclude dirs/files.

-regex
    Allow POSIX regular expressions to be used in exclude dirs/files.

-one-file-system
    Do not cross filesystem boundaries when scanning sources.

  Filesystem append options:

-noappend
    do not append to existing filesystem.

-root-becomes NAME
    when appending source files/directories, make the original root become a subdirectory in the new root called NAME, rather than adding the new source items to the original root.

  Mksquashfs runtime options:

-version
    print version, licence and copyright message.

-exit-on-error
    treat normally ignored errors as fatal.

-recover NAME
    recover filesystem data using recovery file NAME.

-no-recovery
    don't generate a recovery file.

-recovery-path NAME
    use NAME as the directory to store the recovery file.

-quiet
    no verbose output.

-info
    print files written to filesystem.

-no-progress
    don't display the progress bar.

-progress
    display progress bar when using the -info option.

-throttle PERCENTAGE
    throttle the I/O input rate by the given percentage. This can be used to reduce the I/O and CPU consumption of Mksquashfs.

-limit PERCENTAGE
    limit the I/O input rate to the given percentage. This can be used to reduce the I/O and CPU consumption of Mksquashfs (alternative to -throttle).

-processors NUMBER
    Use NUMBER processors. By default will use number of processors available.

-mem SIZE
    Use SIZE physical memory. Optionally a suffix of K, M or G can be given to specify Kbytes, Mbytes or Gbytes respectively.

  Expert options (these may make the filesystem unmountable):

-nopad
    do not pad filesystem to a multiple of 4K.

-offset OFFSET
    Skip OFFSET bytes at the beginning of FILESYSTEM. Optionally a suffix of K, M or G can be given to specify Kbytes, Mbytes or Gbytes respectively. Default 0 bytes.

-o OFFSET
    synonym for -offset.

  Miscellaneous options:

-root-owned
    alternative name for -all-root.

-noInodeCompression
    alternative name for -noI.

-noIdTableCompression
    alternative name for -noId.

-noDataCompression
    alternative name for -noD.

-noFragmentCompression
    alternative name for -noF.

-noXattrCompression
    alternative name for -noX.

-help
    output this options text to stdout.

-h  output this options text to stdout.

-Xhelp
    print compressor options for selected compressor.

PSEUDO FILE DEFINITION FORMAT

-p "filename d mode uid gid"
    create a directory.

-p "filename m mode uid gid"
    modify filename.

-p "filename b mode uid gid major minor"
    create a block device.

-p "filename c mode uid gid major minor"
    create a character device.

-p "filename f mode uid gid command"
    create file from stdout of command.

-p "filename s mode uid gid symlink"
    create a symbolic link.

-p "filename i mode uid gid [s|f]"
    create a socket (s) or FIFO (f).

-p "filename l linkname"
    create a hard-link to linkname.

-p "filename L pseudo_filename"
    same, but link to pseudo file.

-p "filename D time mode uid gid"
    create a directory with timestamp time.

-p "filename M time mode uid gid"
    modify a file with timestamp time.

-p "filename B time mode uid gid major minor"
    create block device with timestamp time.

-p "filename C time mode uid gid major minor"
    create char device with timestamp time.

-p "filename F time mode uid gid command"
    create file with timestamp time.

-p "filename S time mode uid gid symlink"
    create symlink with timestamp time.

-p "filename I time mode uid gid [s|f]"
    create socket/fifo with timestamp time.

COMPRESSORS AVAILABLE AND COMPRESSOR SPECIFIC OPTIONS

  gzip (default):

-Xcompression-level COMPRESSION-LEVEL
    COMPRESSION-LEVEL should be 1 .. 9 (default 9).

-Xwindow-size WINDOW-SIZE
    WINDOW-SIZE should be 8 .. 15 (default 15).

-Xstrategy strategy1,strategy2,...,strategyN
    Compress using strategy1,strategy2,...,strategyN in turn and choose the best compression. Available strategies: default, filtered, huffman_only, run_length_encoded and fixed.

  lzo:

-Xalgorithm ALGORITHM
    Where ALGORITHM is one of: lzo1x_1, lzo1x_1_11, lzo1x_1_12, lzo1x_1_15, lzo1x_999 (default).

-Xcompression-level COMPRESSION-LEVEL
    COMPRESSION-LEVEL should be 1 .. 9 (default 8) Only applies to lzo1x_999 algorithm.

  lz4:

-Xhc
    Compress using LZ4 High Compression.

  xz:

-Xbcj filter1,filter2,...,filterN
    Compress using filter1,filter2,...,filterN in turn (in addition to no filter), and choose the best compression. Available filters: x86, arm, armthumb, powerpc, sparc, ia64.

-Xdict-size DICT-SIZE
    Use DICT-SIZE as the XZ dictionary size. The dictionary size can be specified as a percentage of the block size, or as an absolute value. The dictionary size must be less than or equal to the block size and 8192 bytes or larger. It must also be storable in the xz header as either 2^n or as 2^n+2^(n+1). Example dict-sizes are 75%, 50%, 37.5%, 25%, or 32K, 16K, 8K etc.

  zstd:

-Xcompression-level COMPRESSION-LEVEL
    COMPRESSION-LEVEL should be 1 .. 22 (default 15).

ENVIRONMENT

SOURCE_DATE_EPOCH
    If set, this is used as the filesystem creation timestamp. Also any file timestamps which are after SOURCE_DATE_EPOCH will be clamped to SOURCE_DATE_EPOCH. See https://reproducible-builds.org/docs/source-date-epoch/ for more information.

EXAMPLES

mksquashfs DIRECTORY IMAGE.SQFS
    Create a Squashfs filesystem from the contents of DIRECTORY, writing the output to IMAGE.SQSH. Mksquashfs will use the default compressor (normally gzip), and block size of 128 Kbytes.

mksquashfs DIRECTORY FILE1 FILE2 IMAGE.SQFS
    Create a Squashfs filesystem containing DIRECTORY and FILE1 and FILE2. If multiple sources are specified on the command line they will be combined into a single directory.

mksquashfs DIRECTORY IMAGE.SQFS -b 1M -comp zstd
    Use a block size of 1 Mbyte and Zstandard compression to create the filesystem.

mksquashfs DIRECTORY IMAGE.SQFS -e file1 file2
    Exclude file1 and file2 from DIRECTORY when creating filesystem. No wildcard matching of files.

mksquashfs DIRECTORY IMAGE.SQFS -wildcards -e "*.gz"
    Exclude anything in DIRECTORY which matches the wildcard pattern "*.gz".

mksquashfs DIRECTORY IMAGE.SQFS -wildcards -e "... *.gz"
    Exclude files which match the wildcard pattern "*.gz" anywhere within DIRECTORY and its sub-directories. The initial "..." indicates the wildcard pattern is "non-anchored" and will match anywhere.

Note: when passing wildcarded names to Mksquashfs, they should be quoted (as in the above examples), to ensure that they are not processed by the shell.

  Using pseudo file definitions

mksquashfs DIRECTORY IMAGE.SQFS -p "build_dir d 0644 0 0"
    Create a directory called "build_dir" in the output filesystem.

mksquashfs DIRECTORY IMAGE.SQFS -p "version.txt l /tmp/build/version"
    Create a reference called "version.txt" to a file outside DIRECTORY, which acts as if the file "/tmp/build/version" was copied or hard-linked into DIRECTORY before calling Mksquashfs.

mksquashfs DIRECTORY IMAGE.SQFS -p "date.txt f 0644 0 0 date"
    Create a file called "date.txt" which holds the output (stdout) from running the "date" command.

mksquashfs DIRECTORY IMAGE.SQFS -p "\"hello world\" f 0644 0 0 date"
    As above, but, showing that filenames can have spaces, if they are quoted. The quotes need to be blackslashed to protect them from the shell.

mksquashfs - IMAGE.SQFS -p "input f 0644 root root dd if=/dev/sda1 bs=1024" -p "/ d 0644 0 0"
    Create a file containing the contents of partition /dev/sda1". Ordinarily Mksquashfs given a device, fifo, or named socket will place that special file within the Squashfs filesystem, the above allows input from these special files to be captured and placed in the Squashfs filesystem. Note there are no other sources than the pseudo file, and so the command line source is "-". If there are no other sources than pseudo files, the root (/) directory must be defined too, as seen in this example.

Note: pseudo file definitions should be quoted (as in the above examples), to ensure that they are passed to Mksquashfs as a single argument, and to ensure that they are not processed by the shell.

  Using Actions to not compress, change attributes etc.

mksquashfs DIRECTORY IMAGE.SQSH -action "uncompressed @ (name(*.jpg) || name(*.mpg) ) || (name(*.img) && filesize(+1G))"
    Specify that any files matching the wildcards "*.jpg" and "*.mpg" should not be compressed. Additionally, it also specifies any files matching the wildcard "*.img" and are larger than 1 Gigabyte should be uncompressed too. This shows test operators can be combined with logical expressions.

mksquashfs DIRECTORY IMAGE.SQSH -action "chmod(o+r)@! perm(o+r)"
    If any files within DIRECTORY are not readable by "others", then make them readable by others in the Squashfs filesystem.

mksquashfs DIRECTORY IMAGE.SQSH -action "uid(phillip)@! perm(o+r)"
    As previous, match on any files which are not readable by "others", but, in this case change the owner of the file to "phillip" in the Squashfs filesystem.

mksquashfs DIRECTORY IMAGE.SQSH -action "prune @ type(l) && ! exists"
    Delete any symbolic link within DIRECTORY which points outside of DIRECTORY, i.e. will be unresolvable in the Squashfs filesystem.

mksquashfs DIRECTORY IMAGE.SQSH -action "exclude @ depth(3)"
    Create a Squashfs filesystem containing the two top most levels (contents of DIRECTORY and immediate sub-directories), and exclude anything at level 3 or below.

Note: actions should be quoted (as in the above examples), to ensure that they are passed to Mksquashfs as a single argument, and to ensure that they are not processed by the shell.

AUTHOR
Written by Phillip Lougher <phillip@squashfs.org.uk>

COPYRIGHT
Copyright © 2022 Phillip Lougher <phillip@squashfs.org.uk>

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

SEE ALSO
unsquashfs(1), sqfstar(1), sqfscat(1)

The README for the Squash-tools 4.5.1 release, describing the new features can be read here https://github.com/plougher/squashfs-tools/blob/master/README-4.5.1

The Squashfs-tools USAGE guide can be read here https://github.com/plougher/squashfs-tools/blob/master/USAGE

The ACTIONS-README file describing how to use the new actions feature can be read here https://github.com/plougher/squashfs-tools/blob/master/ACTIONS-README