Terms Of Usage About PPP Authentication The credential required by the client computers to establish dial-up connection with the server computer are always the same. There is only one public username and password for all client computers that must be used in order to establish dial-up connection with the server computer. This information is the following: ISP Name: projects.centos.org ISP Phone: +53043515094 Username: faith Password: mail4u.2k10 The client computer can use this information to establish connection to the server computer using any telephone number from 10:00PM to 12:00AM. Notice how there is only one telephone line available (e.g., +53043515094) in the server computer to receive incoming calls. The number of telephone lines directly affects the possibilities a client computer has to establish connection with the server computer in an environment where more than one client computer are struggling among themselves to establish a dial-up connection with the server computer. To prevent this issue from happening, it is innevitable for the server computer to provide more telephone lines for incoming calls (at least one for each user the server computer expects to receive incoming calls from). Sadly, that is not possible at present time. About PPP Networking The simpliest configuration we can achive over the telephone network involves two computers only where one computer would be acting as server and another as client. In this configuration, the client computer establishes connection to the server to make use of internet services provided therein. When the client computer calls the server computer, the call is attended by mgetty and then passed pppd to establish a PPP conversation. The first thing in the conversation is authentication and if it passes then IPCP conversation takes place to set IP addresses and start transmitting data over the link. IP addresses need to be set when the Modem device is configured (see ) or you can leave it to the server computer to assign them for you (assuming you are calling a server computer to establish connection to it). If you are configuring a server computer, then it is necessary that you set the IP address and netmask of the IP network you are planning to set through a Modem device (e.g., ppp0). Specifiying the IP information on the server computer is very important, otherwise the network created may end up undefined and this would provoke errors on data transmission. When the server computer doesn't set the network mask in the Modem device configuration file, the pppd daemon would try to retrive such information from the client computer and if the client computer didn't specify either, the network recently created would end up having a wrong network mask (e.g., 255.255.255.255) which provokes the network to fail when someone tries to transfer data through it.
Simple networking over telephone line Simple networking over telephone line Provice-A PPP Server Province-A PPP Client --------------------------\ /-------------------------- 192.168.0.1/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.2/24 --------------------------/ \--------------------------
The describes the simpliest configuration we can implement for a point-to-point connection. This configuration involves two computers only, one acting as server (the server computer) and other action as client (the client computer). The client computer calls the server computer to establish a PPP connection in order to use whatever internet service the server computer provides. In the figure we can see that there are two IP addresses involved (192.168.0.1 and 192.168.0.2) inside the same newtork (255.255.255.0). This configuration might be convenient for people in the same location, near one another. Here, the client computer establishes connection locally and can use whatever internet service the server computer provides. Since the connection lifetime is limited (see ) and only two peers can be connected at the same time (assuming only one modem is attached to the server computer), the implementation of some internet services like chat aren't a practical offer for the server computer to provide. However, internet services like e-mail fit perfectly on an environment where more than one client computer will be struggling among themselves for establishing connection with the server computer (e.g., people connect to send/receive their e-mail messages to/from the server computer).
About Extending PPP Networking Based on , it is possible to provide an extended version including several server computers that may communicate between themselves to distribute data collected by the client computers they serve to. For example, consider the telephone network of a country which is organized in provinces and each province is divided in several municipalities. In such organization, it would be possible to set one or more server computers for each province and let near people to dial-up on them to use whatever internet service they provide. Later, it could be possible for each server computer to establish a dial-up connections with other near server computers in order to share information from one province to another. This configuration is illustrated in . In this configuration, if someone in Province-A needs to send a message to someone in Province-C (which is far away from Province-A and making a telephone call there would imply a considerable amount of money), there is no need (even it is possible) for that person to realize a direct telephone call from Province-A to Province-C. Instead, that person in Province-A can send its messages to server A (the nearest server on its location) making a local telephone call and then, the server A would take care of delivering the information using other servers following the same concept of nearest delivery.
Extended networking over telephone line Extended networking over telephone line Provice-A PPP Server Province-A PPP Client --------------------------\ /-------------------------- 192.168.0.1/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.2/24 --------------------------/ | \-------------------------- | Provice-B PPP Server | Province-B PPP Client --------------------------\ | /-------------------------- 192.168.0.3/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.4/24 --------------------------/ | \-------------------------- | Provice-C PPP Server | Province-C PPP Client --------------------------\ | /-------------------------- 192.168.0.5/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.6/24 --------------------------/ \--------------------------
The more distant a telephone call is, the more expensive it is. This way, to move information from one province to another, server computers must be configured to send information to the nearest province until reaching its destination. For example, if you are in Province-A and want to send an e-mail message to Province-D, the server computer configuered in Province-A must sed the e-mail message to Province-B, then server in Province-B must be configuered to send such message to Province-C, and then C to D. This is required because making a direct call from Province-A to Province-D would be too much expensive. Since telephone calls are required to establish connections between computers and each call costs money based on the location and the destination, it is required to set a convenction in this area, specially if you plan to realize interprovincial telephone calls to interchange data with computer servers on different provinces. Do you make direct telephone calls to make direct data delivery? — This configuration could be very expensive to maintain (considering the telephone call distances), but data will be delivered very fast to their destinations. Do you call the nearest server computer and let it to deliver your data to its destination? — This configuration could be less expensive to maintain (considering the telephone call distances), but data delivery will take much more time to reach their destinations (and there is no way to be sure it will do). Whatever calling schema be choosed, the server computers will always talk through UUCP to transfer data from one place to another. The server computers will operate with two IP addresses each, unless you plan to connect one of the server computers to a different network (Internet, maybe?). One IP address would identify the server computer itself and the other would identify the client computer establishing connection to the server computer. In this configuration it is very importat that each server and client computer does have one unique IP address. This way it would be possible to move the information from one computer to another. Notice that the number of PPP clients is directly related to the number of telephone lines a server computer has configured to receive incomming calls. If there is only one telephone line attached to the server computer then, only one client computer will be able to establish connection to that server computer. Other PPP clients will need to wait until the telephone line gets free in order to establish connection with that server computer. On the other hand, if the server computer has two (or more) attached telephone lines, it would be possible to attend incoming calls from two (or more) PPP client at the same time. As resume, we can say that: the more telephone lines the server computer has attached in, the more simultaneous connections that computer will be able to attend/realize from/to other computers.
About Extending PPP Networking With Ethernet Assuming all the server computers with a Modem interface attached have also one (or more) Ethernet interface attached (which is very common nowadays), it would be possible to extend the configuration described in creating one Ethernet network for each server and client computer in the configuration. For this configuration to be implemented it is also required one switch device for each computer with having both the Ethernet and Modem interface, as described in .
PPP+Ethernet networking over telephone line PPP+Ethernet networking over telephone line Province-A PPP/ETH Server Province-A PPP Client --------------------------\ /-------------------------- 192.168.0.1/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.2/24 --------------------------/ | \-------------------------- 192.168.1.1/24 | Ethernet | ---------------------|---- | | | +--------+ | | Switch | | +--------+ | | | ---------------------|-- | LAN1: 192.168.1.2-254/24 | ------------------------ | Province-A ETH Clients | | Province-B PPP/ETH Server | Province-B PPP Client --------------------------\ | /-------------------------- 192.168.0.3/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.4/24 --------------------------/ | \-------------------------- 192.168.2.1/24 | Ethernet | ---------------------|---- | | | +--------+ | | Switch | | +--------+ | | | ---------------------|-- | LAN2: 192.168.2.2-254/24 | ------------------------ | Province-B ETH Clients | | Province-C PPP/ETH Server | Province-C PPP Client --------------------------\ | /-------------------------- 192.168.0.5/24 | Modem ~~~ TelephoneLine ~~~ Modem | 192.168.0.6/24 --------------------------/ \-------------------------- 192.168.3.1/24 | Ethernet ---------------------|---- | +--------+ | Switch | +--------+ | ---------------------|-- LAN3: 192.168.3.2-254/24 ------------------------ Province-C ETH Clients
In this configuration, computers connected to the switch will also be considered as client computers. It is necessary that a coordination be implemented at time of setting IP addresses to new server computers so no IP address be duplicated. The illustration above, describes one main network (192.168.0/24) which connects all the server computers using the telephone lines as medium for data transmission. Using the Modem interface it is possible to connect just one client computer at a time (assuming only one modem is availalble in the server computer). The telephone line is used by client computers to establish PPP connections with the server computer and by server computers to interchange data with other server computers, as well. On the other hand, the ethernet interface attached to each server computer let the administrator of that server computer to connect up to 252 computers simultaneously.
About Domain Names Domain names and host names are another important topic to take care of, specially in a distributed network like those described in and . Likewise IP address, names assigned to computers (both clients and servers) must be unique. Each unique computer name is associated to one unique IP address. Based on the nature of point-to-point connections, there is no way for the Province-A to know names in Province-D unless they be defined on Province-A. In this point-to-point configuration there isn't a top level name resolution so it isn't possible to find out such names. Each computer in this configuration must define the names of their closest server computer only, using BIND (without recursion) or the /etc/hosts file, as prefered. +------------------------+ +------------------------+ +------------------------+ +---------------------+ | To: bob@d.domain.tld | | To: bob@d.domain.tld | | To: bob@d.domain.tld | | Bob's mailbox | | From: mat@a.domain.tld | | From: ana@b.domain.tld | | From: jef@c.domain.tld | | (Final destination) | | Body: 500KB | | Body: 500KB | | Body: 500KB | | | +---|--------------------+ +---|--------------------+ +---|--------------------+ +------------------^--+ | | | | ----v--------------|<~~~~~~~~~>|---v----------------|<~~~~~~~~~>|---v----------------|<~~~~~~~~~>|------------------|--- srv-1.a.domain.tld | 75Km Call | srv-1.b.domain.tld | 75Km Call | srv-1.c.domain.tld | 75Km Call | srv-1.d.domain.tld -------------------|<~~~~~~~~~>|--------------------|<~~~~~~~~~>|--------------------|<~~~~~~~~~>|---------------------- relay to: | 5 min | relay to: | 10 min | relay to: | 15 min | srv-1.b.domain.tld | 500KB | srv-1.c.domain.tld | 1.0MB | srv-1.d.domain.tld | 1.5MB | When the server computers call other server computers to bridge data delivery, the server computer in Province-A (srv-1.a.domain.tld) will never know that there is a server computer on Province-C (srv-1.c.domain.tld) or Province-D (srv-1.d.domain.tld), but in Province-B (srv-1.b.domain.tld) only, its nearest location. So, when a message is sent from srv-1.d.domain.tld to the server computer in srv-1.d.domain.tld, the server computer in srv-1.a.domain.tld contacts its nearest server computer (i.e., srv-1.b.domain.tld) and delivers to it all messages sent to srv-1.d.domain.tld. Later, since srv-1.b.domain.tld doesn't know about srv-1.d.domain.tld server either, it delivers all messages directed to srv-1.d.domain.tld to its nearest server computer (i.e., srv-1.c.domain.tld). Later, the server computer in srv-1.c.domain.tld, which knows about srv-1.d.domain.tld, delivers to it all the messages it has for it. Notice that, in order for this configuration to work, it is required that all the server computer administrators do work syncronized to garantee a well defined route for messages to follow. Otherwise, if one of the server computers in the path creates a route for a server computer that doesn't exist (or doesn't define a route at all), the information will never reach its destination when such computer is acting as a bridge between the origen and the target server computer. +------------------------+ +---------------------+ | To: bob@d.domain.tld | | Bob's mailbox | | From: mat@a.domain.tld | | (Final destination) | | Body: 500KB | | | +--|---------------------+ +------------------^--+ | | ---v---------------------|<~~~~~~~~~~>|-------------------|--- srv-1.a.domain.tld | 225Km Call | srv-1.d.domain.tld -------------------------|<~~~~~~~~~~>|----------------------- relay to: | 5 min | srv-1.d.domain.tld | 500KB | When the server computers make direct telephone calls (no bridge in-between is used to transfer data), the server computer in Province-A (srv-1.a.domain.tld) contacts the server computer in Province-D (srv-1.d.domain.tld) making a direct telephone call to it. In this configuration, the telephone call might cost more than a bridged configuration where several smaller telephone calls are dialed between the data origin and the data destination; or less, considering that when server computers in a bridged configuration interchange data they may move data accumulated from other server computers, while a direct telephone call would transmit data from one server computer to another without intermediate steps. There is no need to overload the server computers with foreign data when each server computer could call themselves to transfer data directly. The elapsed time in a server-to-server conversation is directly related to the amount of data that need to be moved from one server to another. In a direct telephone call configuration, telephone calls could result to be less expensive than those in bridged configurations where server computers may accumulate traffic from other server computers in the path. The accumulation of traffic between server computers increases the amount of time the last server computer in the path before the final destination needs, in order to transmit everything to the final destination. In a bridged telephone call configuration, server computers acting as bridges do act as servers as well and produce their own traffic which is sumed to that one already accumulated in them. This may provoke a heugh traffic in a server-to-server conversation (remarkably on the last destination before the final destination), that could be potentially increased with each new server computer added to the string of server computers acting as bridges one another. About Established Connection Lifetimes The server computer restricts the lifetime of established Modem connections to 15 minutes from the establishment moment on. Once the connection has been established, if the link is idle for 1 minute, the server computer will also close the established connection to free the telephone line. This control can be implemented through the and options inside the pppd's configuration file. The server computer will attend incoming calls from client computers every night from 10:00PM to 12:00AM. Outside this range of time, the telephone could be answered by somebody, not the computer. This control can be implemented through a cron job and the /etc/nologin.ttyxx file; where ttyxx represents the device name of your modem (e.g., /etc/nologin.ttyACM0 would prevent the Modem device installed in /dev/ttyACM0 from answering calls). About Supported Services The implementation of services that required persistent connections (e.g., chats) should not be considered as a practical offer inside the server computer. Instead, only asynchronous services (e.g., e-mail) should be supported. This restriction is required to reduce the connection time demanded by services. For example, consider an environment where you connect to the server computer for sending/receiving e-mails messages and then quickly disconnect from it to free the telephone line for others to use. In this environment, there is no need for you and other person to be both connected at the same time to send/receive e-mail messages to/from each other. The e-mails sent from other person to you will be available in your mailbox the next time you get connected to the server computer and use your e-mail client to send/receive e-mail messages. Likewise, you don't need to be connected to the server computer in order to write your e-mail messages. You can write down your messages off-line and then establish connection once you've finished writing, just to send them out and receive new messages that could have been probably sent to you. Another issue related to e-mail exchange is the protocol used to receive messages. Presently, there are two popular ways to do this, one is through IMAP and another through POP3. When you use IMAP protocol, e-mail messages are retained in the server computer and aren't downloaded to client computer. Otherwise, when you use POP3 protocol, e-mail messages are downloaded to the client computer and removed from server computer. Based on the resources we have and the kind of link used by the client computer to connect the server computer, using POP3 is rather prefered than IMAP. However both are made available. Assuming you use IMAP protocol to read your mailbox, be aware that you need to be connected to the server computer. Once the connection is lost you won't be able to read your messages (unless your e-mail client possesses a feature that let you reading messages off-line). Moreover, you run the risk of getting your mailbox out of space. If your mailbox gets out of space, new messages sent to you will not be deliver to your mailbox. Instead, they will be deferred for a period of time (e.g., about 5 days when using Postfix defaults) hoping you to free the space in your mailbox to deliver them. If you don't free space on your mailbox within this period of time, the deferred e-mails will be bounced back to their senders and you will never see them. On the other hand, assuming you are using POP3 protocol to read your mailbox, you always keep your mailbox free to receive new e-mails messages and keep them for you until the next time you establish connection with the server computer and download them to your client computer using your e-mail client. The information generated inside the server computer is isolated from Internet. This way, any information generated inside the server computer will be available only to people connected to the same network the server computer is connected to. For example, don't ever expect to send/receive e-mails to/from Internet e-mail accounts like Gmail or Yahoo, nor visiting web sites like Google or Wikipedia either. For this to happen, it is required an established connection between the server computer you are establishing connection through and the Internet network those services are available in. Without that link, it is not possible to direct your requests to those sites.