<sect1 id="configurations-dialup-client">

    <title>The Client Computer</title>

    <sect2 id="configurations-dialup-client-install">

    <title>Installing Client Computer</title>

    <para>

        ...

    </para>

    </sect2>

    <sect2 id="configurations-dialup-client-config">

    <title>Configuring Client Computer</title>

    <para>

        ...

    </para>

    <sect3 id="configurations-dialup-client-config-conn">

    <title>Establishing Dial-Up Connection</title>

    <para>

        To establish connection from the client computer to the server

        computer you should configure the client computer to dial-up

        the server computer, using the following information:

    </para>

<screen>

 ISP Name: server.example.com

ISP Phone: +53043515094

 Username: client.example.com

 Password: mail4u

</screen>

    <para>

        To estabalish a dial-up connection from the client computer to

        the server computer, you need to determine the modem location

        assigned by the operating system, so you can instruct

        applications like <command>system-config-network</command> the

        correct device they will to talk to. This configuration

        process has been greatly simplified by the

        <command>wvdialconf</command> command distributed with the

        <package>wvdial</package>

        package. To do this, run the following command and pay

        attention to the three last lines of its output:

    </para>

    <screen>wvdialconf /etc/wvdial.conf</screen>

<screen>

Scanning your serial ports for a modem.

ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud

ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud

ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.

Port Scan<*1>: S1   S2   S3   

WvModem<*1>: Cannot get information for serial port.

ttyACM0<*1>: ATQ0 V1 E1 -- OK

ttyACM0<*1>: ATQ0 V1 E1 Z -- OK

ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK

ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK

ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK

ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK

ttyACM0<*1>: Modem Identifier: ATI -- LT V.90 1.0 MT5634ZBA-USB

Data/Fax Modem (Dual Config) Version 5.18e

ttyACM0<*1>: Speed 4800: AT -- OK

ttyACM0<*1>: Speed 9600: AT -- OK

ttyACM0<*1>: Speed 19200: AT -- OK

ttyACM0<*1>: Speed 38400: AT -- OK

ttyACM0<*1>: Speed 57600: AT -- OK

ttyACM0<*1>: Speed 115200: AT -- OK

ttyACM0<*1>: Speed 230400: AT -- OK

ttyACM0<*1>: Speed 460800: AT -- OK

ttyACM0<*1>: Max speed is 460800; that should be safe.

ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK

Found an USB modem on /dev/ttyACM0.

Modem configuration written to /etc/wvdial.conf.

ttyACM0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"

</screen>

    <para>

        Now, using this information, configure a Modem connection

        using the interface provided by

        <command>system-config-network</command> command. Take care of

        replacing the <filename>/dev/modem</filename> device name by

        that one found by <command>wvdialconf</command>. At this

        point, you can use the button Activate from

        <command>system-config-network</command> to establish the

        Modem connection you just configured.

    </para>

    </sect3>

    </sect2>

</sect1>